Matrix Performance Airsoft AEG Motor (Type: Magnum - High Torque / Long)

"This is a great motor for the price! I buy these for the magnets because I just use the cans to build frankentorque motors. These magnets are on par with g&p devil jets, but they're about 90 bucks less. I highly recommend these for the magnets, but they work amazingly stock as well. My only suggestion and the reason for four stars is that the pinion isn't the best. Replace that and you have a great motor that will serve you well.

"This motor is great.... except for one thing. The screws in the back of the motor stick out a little bit too far to fit in the motor mount for my cyma m14. However i did a bit of grinding on the mount and it fits great and works like a charm. Thumbs up overall

"Buyers beware, just confirmed that WITHOUT MODIFICATION, this will NOT fit into Tokyo Marui's P90 motor cage (Possibly P90s of other brands as well).

The problem is that the heads of the 2 black screws that secure the base plate of the motor are way too thick for the motor cage to shift far enough to latch back together.

The simple fix I've found is go to a hardware store and look for metric 0.5mm x 10mm screws that have comparably more flushed heads.

Once you got the new screws, simply replace the original black screws ONE AT A TIME (keep one black screw securely in place so you can screw the new screw in without the base plat popping open on you, as you'll need to use some force to fit the new screws all the way down. Once the first new screw is in tight, you can then remove the 2nd black screw and replace it with another new screw, again, make sure it sits all the way down.)

Also, originally there are 2 washers on each of the black screws (4 total), remember to place at least one washer in each of your replacement screws before screwing them in.

Obviously once you've done this you'll void all warranty, so do it at your own risk.

Once it's all fitted together properly, this motor performs flawlessly. If not a bit hot, which's a common problem for all the high speed motors anyway. So try to avoid doing long bursts with these high speed motors installed.

1 star deducted for the fitting problem and time spent replacing screws, but otherwise it works really well.

"This is a great motor! The neo magnets are very strong. I put this particular motor in my Echo1 ST6 with a MOSFET and 16gauge wire. The stock motor with a M110 and the upgraded wire setup was getting about 14-15rps (tested with an excortech chrono). I put a M120 and this motor into the gun with a shim job, it now shoots at 23rps! The only problem i had was that the pinion on the motor was slightly to large for the opening in the gearbox, with a quick mod to the gearbox it worked fine.

Pros:
Its a neodymium motor
Huge increase in rof

Cons:
Pinion was slightly to large

"I love the motor, the rate of fire increased on my P90 by a few rounds per second. I basically got this as a replacement motor and it works wonderfully, well worth the money! The only con is that it didn't fit in the P90 motor cage quite right, so the motor height is just a tad bit high for my liking. Still no screeching or anything like that, and it's only pulling an M115 so no gears will break.

"Awesome high-speed motor. If you're looking for ROF, this is your choice. Is a little loud, but that doesn't matter too much. High quality and super fast, but does heat up quick. It can handle the heat, though.

"Well I'm not going to pull this motor out of the box and say "WOW THIS IS GREAT" without even installing it yet, like I did a year ago, but lets just say this motor has put down some really high end name brand motors in their place, I have run the motor on an Echo1 mp5 at 400 fps and 25-27 rps on a 7.4 lipo battery
and on a fully custom m4 at 330 fps and 35 rps. But enough blabbering, to the pros and cons

Pros:
gives great ROF
pulls up to m130 springs +++++
great to have of you want a high speed build you can use in fields
lasts longer than your gun

Cons:
On a 9.6 or any lipo the motor heats up really quick giving you a scare, however, its always fine

Overall:I would extremely reccomend this motor to any long time tech, or noob tech like I was when I got it!

"This is a great motor for high speed applications. I had it paired with a AIM Top Tornado Speed gearbox in an M16 and was achieving around 25 rounds per second with a 9.6v large type. You will want two things with it though: first you'll want a vented motor plate because this motor gets pretty hot (to be expected). second, as everyone else says you will definitely want a different pinion gear. I wouldn't even fool with the stock one as it will strip. I must say though the motor magnets are so strong that when it does the metal shreds will go down and stick to the motor (not all of them, but alot of the shreds). Personally, I was flanking a team with a friend and this stripped right as our postions were compromised which left us totally screwed. Other than the pinion gear its great though.

Pros:
Very high speed
Pulls up to an M120

Cons:
Pinion gear is crap
Gets pretty hot

"This is a good motor for price but i do suggest buying a new pinion gear mine has already stripped after no more than a few hundred shots. The rof is good as long as you have a weaker spring.

old jg motor with 8.4 m120 spring shot 12-13
old motor 9.6 shot 15-17

new matrix motor with 8.4 m120 shot 15-16
matrix motor 9.6 shot 19-22

this is a decent motor besides a few cons

cons
weak pinion gear
heats up a little fast but not to bad
with to strong of spring the gearbox can lock up so don't use over m120

"Great motor, very strong however the pinion gear stripped after mag and a half.

"Bought this motor to upgrade a GR15 for a friend. It's alright. Like all high speed motors, it heats up quite a bit. It doesn't have a whole lot of torque either, but that's also expected. It does have very strong magnets and is constructed quite well. However, the pinion gear is garbage. Stripped after no more than 500 rounds with perfect shimming to the bevel. New SHS pinion shows no wear after several thousand rounds on the same shimming and set up.

Pros:
-good quality
-alright price

Cons:
-pinion is crap
-heats up and doesn't have a lot of torque (compared to SHS, Lonex, and AMP high speed motors)a

This motor is something to consider, but the other options tend to be cheaper and slightly better.

"Good motor and great price. Previously used a TM EG1000. I installed this motor along with an Guarder M140 spring and a 11.1 LiPo. With standard 18.72:1 gears, it fires and reacts quick.

Only complaint is that I had to swap out the pinion gear for the one that was on the TM motor. The stock pinion gear seemed to be made of a softer metal and was actually slightly too large to fit comfortably into the hole in the gearbox. Fitting the standard circular pinion gear onto the Matrix's half-moon shaft was no problem.

"copy that, the gear on the end of the barrel will wear quickly if not adjusted right. The motor is amazingly powerful and fast! strong magnetic pull, everything metal sticks to it. Once I upgraded my parts to fit the torque level this baby puts out, I was more than impressed. My gun sounds alot louder, but fires flawlessly!

"this motor has a great amount of torque, and a great speed. i originally put this into my DMR to replace the JG red motor i put in, but as it turns out the JG red motor has alot more torque (better trigger response) so i left it in. i put this into a JG M733 for a CQB gun (280fps spring) and it rips. on a 9.6 i was getting about 18rps, and instant trigger response.

the only bad thing about this motor is the pinion gear. its angle is steeper than most pinion gears, so its much more likely to break a tooth (happened on the first one i got, sent it back got a new one), and makes the gun alot mroe noisy. it may go away in time due to wear, but i cant be certain on that.

id say just go ahead and get a replacement pinion gear when you get it. it takes the grub screw type, with a D shaped shaft, as opposed to the press fit ones on most motors.

"powerful motor but the the motor should have had been built with CNC Machined End Bell the motor i bought from evike that is called matrix magnum .
i had a triple tuq up laylax gears 170%real pdi spring i have been a tech over 15 year even had my own shop year ago ,so i put the motor in and it rum smooth and very quit battery was G&P 9.6v3300 mah
after about 300 rounds i started fire one shot at a time then it sounded like broken glass and everything stopped .
so i took off the end of the butt plate and 4 black plastic parts came out out all the motors i have installed this i have never seen at all.
yes this is a powerful motor and yes the $ is good ! but this motor needs to be revised we did a test this is not even high grade Polycarbonate it is a brittle low grade plastic .
as soon as they fix this it will be the best motor for the money out there ..............