Perun MOSFET for Tokyo Marui Spec P90 Series AEG Gearboxes

Features

• Ultra compact MOSFET designed for P90 gearboxes
• Adjustable trigger sensitivity with 5 adjustable levels
• Programmable firing modes
• Active Braking for perfect shot management
• Precocking function for improved trigger response
• Binary trigger for faster semi-auto rate of fire
• Rate of fire reduction mode for increased realism
• Low battery voltage alarm helps protect your lithium battery packs
• Detection mode prepared to work with dual sector gears
• Built-in diagnostic system helps monitor the rifle and MOSFET for easier troubleshooting
• Electronic fuse cuts off the battery circuit in case of malfunction, protecting the MOSFET and your rifle

Perun for P90 replaces trigger bar and mechanical contacts in your P90 replica and provides lots of useful features. Magnetic sensors coupled with a magnet installed directly on the trigger, allow to remove the bar that connects trigger with the gearbox, making trigger pull much smoother. Proprietary cut-off lever (comes with the mosfet) works with an optical sensor to eliminate all problems with single fire function.

Selectable firing modes
User can choose firing modes available after short or long pull of the trigger: SEMI ONLY, BINARY, SEMI-AUTO, SEMI-BURST, BURST-AUTO.

Adjustable trigger sensitivity
The trigger can be set to 5 sensitivity levels for both first and second trigger stage, ranging from short pull needed to fire a shot, to a long one. No modification to the trigger or the gearbox is needed and the trigger sensitivity change is possible even in the field.

Active brake
Active brake stops the motor after each shot preventing spring compression or in case of replicas with high rate of fire, overspin (double shot problem).

Precocking
Fast trigger response can be a matter of victory or defeat, especially in CQB situations. With precocking enabled, piston will remain in rear position after each shot with the spring already compressed, ensuring that next shot will be fired immediately after you pull the trigger. To release the spring after using precocking, pull the trigger and hold it for 2 seconds, after which a second shot will be fired, this time with no precocking and fully braked.

Binary trigger
Allows for easy double shots in semi-automatic setting. After enabling this mode, if semi-automatic fire is set, shots will be fired not only when the trigger is pulled, but also when it is released.

Rate of fire reduction
Reduce the rate of fire in automatic or burst fire to save ammo or make the replica shoot in a more realistic fashion.

Low battery voltage alarm
Dedicated for Li-Po and Li-Ion batteries. Should the battery voltage fall to a dangerously low level, user will be notified by short sound signals that are repeated every minute. This may also be freely switched on and off.

DSG
A sector gear detection mode specially prepared to work with dual sector gears.

Diagnostic system
Constantly monitors the replica and the mosfet itself. In case of any problems, immediately lets you know what it might be, making troubleshooting much easier.

Electronic fuse
Will save your replica and battery in case of a major malfunction. It will automatically disconnect the battery when a short circuit or blocked motor is detected.

Programming of all the settings is done solely by using a button and multicolor LED diode mounted in the battery compartment and the trigger. That allows changing the settings in any moment, in a matter of seconds, even under enemy fire. All settings are set independently for each selector position, so you can program the mosfet exactly the way you want, for example semi on semi and binary trigger on auto.Perun for P90 works without problems with any battery from, 7 V to 17 V. It can also be used with most extreme setups.

Manufacturer: Perun Airsoft

Specifications:

Permissible Battery Voltage: 7V to 17V
Compatibility: For use with Tokyo Marui, ACM, Asia Tactical, Classic Army, Cybergun, CYMA, Double Bell, J Tactical, JG and other compatible P90 AEG rifles
Wiring: Universal-wired

NOTE: Replicas compatible with this mosfet are models made by: Tokyo Marui, ACM, Asia Tactical, Classic Army, Cybergun, CYMA, Double Bell, J Tactical, JG. King Arms™ P90 and Novritsch™s SSR90 are mostly compatible, but require certain modification. Perun for P90 is incompatible with G&G and Krytac P90™s.

Disclaimer: Professional installation highly recommended. Please use discretion when installing custom parts as fit and compatibility may vary. Modification may be required. Professional installation recommended.

About Perun

Perun was established in 2016 with the aim of designing and manufacturing MOSFET devices and other parts for AEGs. After years of designing and testing, we offer you products that will work reliably even in most extreme situations and enhance the capabilities of your replicas.All of our design work and most of the manufacturing is done in the European Union state of Poland. That allows us to reach our main goal - keep the highest quality possible. We are in constant contact with players, airsoft techs, shops and consult with them to ensure that our products satisfy their needs.