Maxx Model CNC Aluminum Advanced Speed Trigger for M4 / M16 Series Airsoft AEG (Style: B / Red)

"This trigger is absolutely the best and looks awesome! I've installed two of these; one paired with a Gate TITAN II and one with a G&G ETU 2.0. Both can be adjusted to be crazy sensitive. However, there are a few things you might have to do to get it to fit:

- The trigger can be a little loose in the gearbox. I used some shims to tighten it up.
- With the G&G ETU, I had to use shims to adjust the height of the trigger and the height of the board so that the head could make proper contact with the switch.
- I had to shave down the safety lever for the safety to function properly. The more you tighten pre-travel, the more you will have to shave the lever.
- Because of the pre-travel screw, I had to make the trigger slot on the receiver larger so that the gearbox could sit in the receiver properly.
- The trigger spring that comes with this is not very strong. I ended up using the original stock one instead. It also doesn’t come with the hex wrench to adjust the screws.

Despite having to do a little grinding and shimming, it’s totally worth it.

"threw this on my polarstar and its suuuper sensitive, would recommend!

"Works great definitely a good quality trigger

"Trigger works great with a Perun V2 Hybrid for those of you wondering. Magnet went on perfectly, no modification required. Really solid trigger and able to achieve a very short travel. Will be purchasing again.

"Just amazing. honestly if you wanted to increase your trigger response, buying this alone would give you results. I paired this with new internals and a Gate Titan V2 advanced and does it rip. Adjustable just to how I like it. looks dope too

"good trigger worked in my e&l mur(VFC style safety I believe) with the Kythera but I did have to Dremel the slot that the trigger goes through in the lower receiver in order to reassemble.

"So I have installed these in all of my guns, one with a gate titan and the other with a E-T-U (Electronic Trigger Unit) they worked great with both of them I could fine tune a gate titan for a hair trigger but still had a little bit of pull left, but with this trigger tuned you could almost blow on the trigger and it would shoot/same with an E-T-U.

If you are using a stock trigger contact mosfet I would not recommend adjusting the trigger a lot for example a hair trigger, because of the trigger reset and if your contacts touch while not shooting you can ruin your contacts. Long story short if you have a stock trigger contact/mosfet get this trigger for show/looks if you have anything like an E-T-U, GATE, and any other electronic mosfet I would recommend this trigger 10/10

"Great trigger I had no problems putting it into an arp9

Only gripe I have is I was expecting the “dark earth” color to be more of a gold but instead it looks orange

I do recommend that once you install it and tune it to your likings, put a little bit of loctite on the screws so they don’t back out as you use the gun

"I used this trigger with a jefftron leviathan mosfet. You have to shave the front off with the leviathan but is shown in their instructions. The forward and backward travel adjustment screws are money. I made a custom spring from a light wire spring for a super short and feather light pull.

"Got the E style for my leviathan, after modifying it I realized I had broken the trigger switch because I didn’t adjust overtravel and it went past the trigger switch and then back over it. It also needed a little more length to properly engage. Pretty good product overall though and the problems I had with it weren’t Maxx’s fault

"I bought the E styled trigger since all the others were on back order. I was not fond of the look of a flat trigger, especially on a SCAR, but I really like the feel of it and Maxx triggers just look good in general.

The quality is top notch. It has no imperfection whatsoever and it is easy to file down (the top portion was interfering with the selector lever with the VFC SCAR trigger assembly).

Where this trigger shines is when in comes to adjustability. You don't have to open the gearbox to tune it as the 1.5mm hex screws are accessible from the outside. You can adjust the maximum distance of travel with the back screw in the neck of the trigger and also the minimum travel with the top screw, meaning you can get that sweet hair trigger if that's what you're into.

Another neat thing about this trigger is that it stays in place in the gun as it is maintained by the top screw mount, but that also means that the trigger is (slightly) harder to get in the gearbox and it causes permanent stress on your trigger assembly. The weak VFC plastic trigger box in always flexing a little bit but it can't flex to the point of breaking once the GB is closed.

"I got the "style B" trigger and it's ergonomics are great! I dropped it into a G&G CM16 gearbox shell with a Wolverine Inferno (Gen2) and it works perfect.

One thing to note (and this is probably just an issue with my model) was the lower screw (the one you use to set the over-travel) was just a tiny bit loose. I just put a drop of Loctite Blue on it and it fits snug.

Very nice. Would recommend.

"Trigger is really really good as you can tune it to be very sensitive or give it a little bit of slack if you want.

Highly recommend if getting a MOSFET

"Great trigger but the internal nub was too short to interface with my polarstar blue FCU trigger board. just required a small credit card slit and some glue

"The trigger looks great works fine just as a trigger should. I paired it with a gate titan basic and runs smoothly.

Only issue is they shipped me the wrong color but that isn’t a big deal, I had already taken it out of the packaging and installed it before I noticed.