(626) 286-0360
Airsoft
Fishing
Air Gun
WE-Tech 30 Round Steel Magazine for WE Open Bolt M4 Airsoft Gas Blowback Series Rifles (Version: CO2 / Tan)
43 Customer Reviews
by Eric L. on 11/12/2024
"Bought 2 and they work perfectly. Better than the one that came with my Scar-L.
by Alexander H. on 11/16/2023
"Hey everyone, I know the facebook comments have been ignored for like ten whole years but I just had to work with customer service and show them the difference between V1 and V2 mags. It is finally confirmed that these are V2 magazines.
by David C. on 06/15/2022
"perfect for my needs, works good all around and no leaks
by dylan c. on 12/30/2020
"good mags ordered 6 of them and non leak
by Anthony B. on 06/20/2019
"These are sooo expensive, but I need them.
Green gas will drop fps with every shot as gas level drops, hpa is more consistent but I hate the high capacity, tube, and carrying a tank aspect of it.
I think high capacity magazines and also the sound of an aeg ruins the sport.
GBB or go home.
One of the 4 I ordered came with a misaligned fill valve but I can still fill it by removing the plate on the bottom.
They work great.
Green gas will drop fps with every shot as gas level drops, hpa is more consistent but I hate the high capacity, tube, and carrying a tank aspect of it.
I think high capacity magazines and also the sound of an aeg ruins the sport.
GBB or go home.
One of the 4 I ordered came with a misaligned fill valve but I can still fill it by removing the plate on the bottom.
They work great.
by thomas K. on 02/18/2019
"Great product and a must have for a GBBR.
Just make sure to lube seals and replace o-rings every so often.
Only complaint is one mag lost a bottom plate during a game.
Just make sure to lube seals and replace o-rings every so often.
Only complaint is one mag lost a bottom plate during a game.
by Anthony B. on 08/09/2018
"This one magazine in my order caused my order to be delayed an extra week at customs
Not much to say besides that, it's a magazine..
Not much to say besides that, it's a magazine..
by Vincent O. on 02/11/2017
"
by Sam O. on 11/07/2016
"Used in WE-Tech Scar-L.
These are pretty nice magazines. The outer shell is aluminum and the internals are pot metal, which is just cast zinc. The valve is brass and steel, the lip and follower are plastic, and the gas route seal is rubber. Efficiency wise, you can pop off all 30 rounds in semi with some CO2 left to spare. Holding down the trigger on full auto from start to finish, you can shoot about 25 rounds with some power but the last 5 struggle to go anywhere. Try a half and half. Half full auto, half semi. You can get all 30 rounds off with that. For those of you who have trouble with getting the CO2 to pierce, make sure the threads of the screw cap on the bottom match up with the treads on the magazine. That will cause problems. Also, oiling the top of the CO2 cartridge helps keep the o-ring squishy and keeps it from cracking. Lubing all o-rings from time to time helps keep the magazine working well. Highly recommended.
These are pretty nice magazines. The outer shell is aluminum and the internals are pot metal, which is just cast zinc. The valve is brass and steel, the lip and follower are plastic, and the gas route seal is rubber. Efficiency wise, you can pop off all 30 rounds in semi with some CO2 left to spare. Holding down the trigger on full auto from start to finish, you can shoot about 25 rounds with some power but the last 5 struggle to go anywhere. Try a half and half. Half full auto, half semi. You can get all 30 rounds off with that. For those of you who have trouble with getting the CO2 to pierce, make sure the threads of the screw cap on the bottom match up with the treads on the magazine. That will cause problems. Also, oiling the top of the CO2 cartridge helps keep the o-ring squishy and keeps it from cracking. Lubing all o-rings from time to time helps keep the magazine working well. Highly recommended.
by Dennis M. on 07/12/2016
"using propane I was able to get 141 solid shots on one fill! Of course it was 80 degrees out in high humidity but still this surprised me
by mark s. on 06/08/2016
"mags have a tendency to spray out the gas if your using a propane canister with low pressure so use fresh cans and always make sure the mag is all the way full and they work amazing.
holds 30 rounds great for training and airsoft but keep in mind you need to count your shots! i carry 4 mags and a spring pistol with 2 mags
holds 30 rounds great for training and airsoft but keep in mind you need to count your shots! i carry 4 mags and a spring pistol with 2 mags
by ricardo h. on 08/04/2015
"Excelent magazines, with one fill of propane they can shoot about 64 rounds. They scratched easily . I buy five magazines and They dont give me any problems at all. Magazines are heavy.
by Max B. on 05/21/2015
"Good quality, and decent price for GBBR mags. I got 3 of these for my 416 and none leaked, and they all fit tightly in the magwell with no wobble. Just to clear things up, these are actually the Gen 3 mags, and they have little bumps on where the mag hits the back of the magwell, so it may take a couple of reloads to break these in. The paint does scratch a bit easy, and the floor plate wobbles a bit, so just take a rubber mallet and gently tap the retaining pieces down, and you're good to go. I would definitely buy these again.
by Robert A. on 09/30/2014
"Very impressed with my WE M4. I have about 2000 rounds through three of these mags. One was leaky when new, but stopped leaking when the seals got some silicone oil on them. Otherwise, I have not had any issues, other than screws and other threaded parts coming use, but that's pretty normal. Use threadlocker on screws and the nozzle if they come loose, and it should solve the problem. I ordered 6 more mags.
by Robert A. on 09/30/2014
"Very impressed with my WE M4. I have about 2000 rounds through three of these mags. One was leaky when new, but stopped leaking when the seals got some silicone oil on them. Otherwise, I have not had any issues, other than screws and other threaded parts coming use, but that's pretty normal. Use threadlocker on screws and the nozzle if they come loose, and it should solve the problem. I ordered 6 more mags.